Frame Pin
Disney Collectibles - Frame Pin
How to Attach a Zinc Frame to Stained Glass
Author: Maureen
Attaching Zinc Frame to Stained Glass
A zinc frame on stained glass panels for the structure and strength is essential. The zinc frame is added, once the design is cut, foiled and soldered. The process of adding a zinc frame is achieved by following seven steps.
1. First measure The length of zinc was required for each page.
2. Then decide whether you want straight cuts or mitered cuts for the corners.
3. Came with a saw or a fine toothed hacksaw cut, the zinc came to the length and angle you need. First, you can cut the pieces long then again cut your dry suit came to the stained glass piece.
4. If you do all the zinc came cut and fitted to your piece, place the glass into the came channels and hold Zinc rather than with t-pins. If you are using cell phone hanger, you would insert them into the came corners during this step.
5. Now flux the corners of the frame and came all the seams, Touch the solder under the
6. Then, solder each joint of the frame and the adjacent Lot seams.
7. Once the first side is done, carefully turn the piece on and repeat the process on this page.
To apply hanging rings to the zinc frame, lightly attached to the flux ring and the portion of the frame, where the ring. The area in which you put the rings should be where the zinc frame meets a solder seam. Next, solder the rings to the zinc frame. Make sure the ring extends over the edge of the frame. If you are a wooden frame to the stained glass pieces include not attach rings to the zinc frame.
Rings facilities can be bought purchased or are comfortable with copper or silver wire. To make your own ring bodies, wrap wire around a pencil or other object to receive, the diameter you need. Then cut it simple, so that a small circle. If you need stronger rings, cut two or three lengths of wire and twist them together. The rotation can be carried by one end of the strands in a vice and the other end into the chuck of a drill. Rotate slowly until the desired amount of twisting is completed. Then wrap the twisted wire cut for a pencil or other object and.
After zinc frame is attached, make sure FLUX remove and use all the flux residues.
Some areas of concern:
Please note that zinc frames are available in different sizes, Widths. Everyone, however, laps over the edge of the glass in the same amount. So go, the only reason to see a larger width is looks. Additional forces can be collected when your stained glass piece is extremely large. Each piece over 30 "wide or tall should be designed in any case in the largest Size zinc frame available.
Mitered cuts look better in my opinion, especially if you are not with a wooden frame. Actually miter cuts are not so much harder to achieve, so why not primarily professional? Small electrical frame cutters 2 "blade, for around $ 20 are available. This is worthwhile in my opinion.
When his mounting frame securely on your work of art, that all edges of the glass in the entire depth of the zinc frames are attached. Otherwise you will be dissatisfied that occur after you solder the pieces together. As already mentioned, T-pins are proposed to be safe and keep the frame firmly and deeply into the glass the channel of the zinc-frame border.
When soldering the corners or the seam lines connecting the frame, you will see a slight increase on the Lot. It is customary to see the actual solder at these points, but is applied after patina, seen together, this mixture and fines. Be careful not to build too much solder at these Places, or it can readily visible when you're done.
After soldering soldering the first side and then turned the art work on the second side, examine the framework that in order to see that it is in the correct position before soldering. Sometimes it can be "adjusted" when you return to the play end.
I run high the hanging rings that hang together were shot, as this much stronger and do not tend to pull apart after the artwork has been for some time. I have seen single wire hooks actually failing and broken one or two pieces and sank. Save yourself grief (take it from me) and only the twisted, therefore stronger Rings facilities.
If a wooden frame, a better look is always produced by mitering the corners of the timber. Simple 45-degree cuts achieved at the end of all frame parts easily so. For mechanical mounting of this piece of the frame, I recommend hanging the use of glue is a good carpenter and a screw for the long-term security. Furthermore Wooden frames in all sizes, including width, thickness and specie of wood. Decide how you want to finish them, paint or stain. This allows You use the right wood for the right job, not the end of painting oak wood. Oak is too expensive and beautiful to hide under paint in my opinion. Fasteners hang that the screws should include in the timber to be used. Build on the stained glass for more information or to sign up for our newsletter please visit: http://www.creativity-in-glass.com
About the Author:
I began to have stained glass about 6 years ago and now I learned I can no stained glass piece I want to build. You can too.
Article Source: ArticlesBase.com -- title = "How to Attach a Zinc Frame to Stained Glass"> How To attach a zinc frame stained glass
 |
US $6.59
| Powered by phpBay Pro |
|
| Powered by phpBay Pro |
Leave a Comment